McCormick-Deering Corn Sheller and Feed Grinder Poster. McCormick-Deering poster advertising corn shellers and feed grinders The poster includes a color illustration of the No 2 Cylinder Corn Sheller At the bottom is a photograph of men using a tractor for a belt-driven feed grinder. When this International Harvester Equipment was new, the dealer would have given you the Operator Manual for your Corn Binder. Also known as the owners, user, or care and operation manual, this 62 page manual is a faithful reproduction of the factory written original.
McCormick-Deering All-Steel Corn Sheller
McCormick-Deering All-Steel Corn Sheller (one-hole)
CAUTION!! Machines must not be operated above their rated speed as this is dangerous and will result in excessive wear and breakage.
INSTRUCTIONS FOR SETTING UP AND OPERATING
The 'right' side of the machine is the crank side or the side having the short shaft projecting with a countersunk hole for the crank set screw.
Remove paint from end of crank shaft and put on crank. Secure with set screw, seeing that point of screw goes into the countersunk hole in shaft. Remove paint from end of long shaft on left side of machine.
For Fan Shellers: Place fan drive sheave No. 2015 in place with the number to the outside. Put fan belt over drive sheave and fan pulley. This belt should run crossed. See illustration. Tighten set screw in sheave. The point of the screw should come in the key-way. Now slip flywheel on shaft and tighten screw.
Mccormick Deering Corn Sheller Parts
Loosen all bearings by applying kerosene and turning the machine. Then oil with a good grade of lubricating oil.
The seed corn tipper may be used with or without the belt drive. When the belt drive is used, the seed corn tipper goes on the crank shaft. When the crank is used, the seed corn tipper goes on the end of the flywheel shaft. Attached by means of set screw. (See illustration No. 3.)
The feed table is bolted in position as shown in illustration No. 2. The heads of the carriage bolts should be inside the hopper.
Adjustments: The rag iron may be adjusted in two directions; an up-and-down movement and a side movement. By looking at illustration No. 4 it will be noted that the picker and stripper wheels and the rag iron form a triangular opening for the ear to pass through. The size of this opening should be made to suit the size of the ears by tightening or loosening the machine bolt (rag iron tension bolt) shown in the same illustration with the wrench applied.
In adjusting the size of the opening, the rag iron should be kept central with the picker and stripper wheels. This is done be removing the nut from the lower bolt in rag iron spring and hopper and moving the top in either direction as required. (See illustration No. 5.) In extremely large corn set the rag iron over toward the stripper wheel.
To obtain the best results in shelling, the machine should be run so that the crank makes about forty-five (45) revolutions per minute or the pulley shaft one hundred and seventy-five (175) revolutions per minute. When driving with belt be sure that this speed is maintained, as any speed in excess of this will have a tendency to cause the shelled corn to pass out with the cobs. The ears should be fed into the sheller point first.
After the operator has shelled several bushels of corn he should be able to make the adjustments to best suit conditions.
- Mccormick Deering Corn Sheller Parts
- Mccormick Deering Hand Corn Sheller Manual Parts
- Hand Corn Sheller Parts
- Mccormick Deering Hand Corn Sheller Manual Pdf
- Mccormick Deering Corn Sheller For Sale
McCormick-Deering Corn Sheller and Feed Grinder Poster. McCormick-Deering poster advertising corn shellers and feed grinders The poster includes a color illustration of the No 2 Cylinder Corn Sheller At the bottom is a photograph of men using a tractor for a belt-driven feed grinder. When this International Harvester Equipment was new, the dealer would have given you the Operator Manual for your Corn Binder. Also known as the owners, user, or care and operation manual, this 62 page manual is a faithful reproduction of the factory written original.
McCormick-Deering All-Steel Corn Sheller
McCormick-Deering All-Steel Corn Sheller (one-hole)
CAUTION!! Machines must not be operated above their rated speed as this is dangerous and will result in excessive wear and breakage.
INSTRUCTIONS FOR SETTING UP AND OPERATING
The 'right' side of the machine is the crank side or the side having the short shaft projecting with a countersunk hole for the crank set screw.
Remove paint from end of crank shaft and put on crank. Secure with set screw, seeing that point of screw goes into the countersunk hole in shaft. Remove paint from end of long shaft on left side of machine.
For Fan Shellers: Place fan drive sheave No. 2015 in place with the number to the outside. Put fan belt over drive sheave and fan pulley. This belt should run crossed. See illustration. Tighten set screw in sheave. The point of the screw should come in the key-way. Now slip flywheel on shaft and tighten screw.
Mccormick Deering Corn Sheller Parts
Loosen all bearings by applying kerosene and turning the machine. Then oil with a good grade of lubricating oil.
The seed corn tipper may be used with or without the belt drive. When the belt drive is used, the seed corn tipper goes on the crank shaft. When the crank is used, the seed corn tipper goes on the end of the flywheel shaft. Attached by means of set screw. (See illustration No. 3.)
The feed table is bolted in position as shown in illustration No. 2. The heads of the carriage bolts should be inside the hopper.
Adjustments: The rag iron may be adjusted in two directions; an up-and-down movement and a side movement. By looking at illustration No. 4 it will be noted that the picker and stripper wheels and the rag iron form a triangular opening for the ear to pass through. The size of this opening should be made to suit the size of the ears by tightening or loosening the machine bolt (rag iron tension bolt) shown in the same illustration with the wrench applied.
In adjusting the size of the opening, the rag iron should be kept central with the picker and stripper wheels. This is done be removing the nut from the lower bolt in rag iron spring and hopper and moving the top in either direction as required. (See illustration No. 5.) In extremely large corn set the rag iron over toward the stripper wheel.
To obtain the best results in shelling, the machine should be run so that the crank makes about forty-five (45) revolutions per minute or the pulley shaft one hundred and seventy-five (175) revolutions per minute. When driving with belt be sure that this speed is maintained, as any speed in excess of this will have a tendency to cause the shelled corn to pass out with the cobs. The ears should be fed into the sheller point first.
After the operator has shelled several bushels of corn he should be able to make the adjustments to best suit conditions.
ATTACHMENTS
The following attachments are shipped 'when ordered':
The basket holder is attached as shown in illustration No. 3. When not in use, it may be folded down.
The pulley for belt drive is attached to the fly-wheel shaft by means of the set screw.
Farmall & IHC Tractors Discussion Board |
Mccormick Deering Hand Corn Sheller Manual Parts
Posted by Mark N. on January 28, 2007 at 16:37:03 from (4.188.215.236):
I have a one hole free standing corn sheller that I am interested in selling. I'm Oliver and this just doesn't fit in. I used at a local Historical Society Open house and the kids just loved throwing full ears in and seeing the empty cobs coming out. It has the usual surface rust but is straight, straight, straight. The hopper pan is excellent. The only thing I know it is missing is the support brace that runs from under the pan to the bottom side of the sheller. It has no welds and the handle still has plenty of blue on it and the decals are still visible on both sides. It was kept on concrete so the legs at the bottom are thick yet unlike most I've seen. I don't really know the pricing on these right now so if anyone has any idea or thoughts let me know. Oh, it also has the belt pulley for a hit and miss engine. Thanks.
Replies:
- Re: McCormick Deering corn shellerJerald18:16:07 05/18/07(0)
- Re: McCormick Deering corn shellerMark 17:03:05 01/28/07(0)
Add a Reply Name: E-Mail: Subject: Comments: Optional Link URL:
|
TRACTOR PARTS | TRACTOR MANUALS |
---|
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ] |
Today's Featured Article - Memories of an IH Super A
Hand Corn Sheller Parts
When I was ? up to 10, I worked on my Papaw's farm in Greeneville, TN every summer. As I grew older (7), it was the thrill of my day to ride or drive on the tractor. My Papaw had a 1954 IH Super A that he bought to replace a Cub. My Papaw raised 'baccer' (tobacco) and corn with the Super A, but the fondest memory was of the sawmill. He owned a small sawmill for sawing 'baccer' sticks. The Super A was the powerplant. When I was old enough (7 or 8), I would get up early and be dressed to ..Mccormick Deering Hand Corn Sheller Manual Pdf
[Read Article]Latest Ad: Non-matched pair of 12.4 x 36 rear tractor tires. Mitas 6 PR. Like new as one can still read the tire size on the face of the lug and LN tube. Good Year Traction Torque @ 50% tread. Pick up, buyer pays shipping and handling, or possible delivery in my travels. Pictures available. No texts.[More Ads]
Mccormick Deering Corn Sheller For Sale
Copyright © 1997-2020 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor Headquarters |